Back to top
Loading…
emuca - vida en los muebles

Zamierzasz usunąć ten koszyk. Jesteś pewny?

Dostęp do obszaru prywatnego Emuca - Vida en los muebles

Forum techniczne

Przedstaw nam swoje wątpliwości dotyczące naszych produktów a nasz Dział Pomocy Technicznej (SAT) skontaktuje się z tobą, aby przedstawić rozwiązanie.

Drawers and slides

Slim drawer for household, kitchen and bathroom

The RAL code of the anthracite grey finish of the sides of the Slim kitchen, household and bathroom drawer is approximately 7043.

The RAL code of the white finish of the sides of the Slim kitchen, household and bathroom drawer is approximately 9003. Although it is necessary to bear in mind that the white silk colour of said drawer is metallized and the RAL codes are for flat colours.

In order to assemble a Slim type kitchen drawer with hinges on the unit doors (hinged doors) it is necessary to use hinges with an opening angle of 165ª or to use spacers, doing so means there will be enough space to pull out the drawer.

Yes, the spacers that are user for assembling kitchen drawers are the same as hinges on unit doors (hinged doors).

The square rail section of the Slim drawer measures 23 mm by 13 mm and the section with trim measures 25 mm by 15 mm.

The minimum unit depth required to install a Slim exterior drawer with push is calculated with the formula: Minimum depth = Depth + 3 mm.
In this case the minimum unit depth needed will be 500 + 3 = 503 mm.

The minimum unit depth required to install a Slim interior drawer with push is calculated with the formula: Min. depth = Depth + 12 mm.
In this case the minimum unit depth needed will be 500 + 12 = 512 mm.

Yes, the Lokbox mechanism is used to fasten the bottom of the drawer to the front part without preventing adjustment of it. It is compatible with the Concept, Slim and Vantage-Q drawers or any drawer. It is especially recommended for very wide drawers used in the furnishings of kitchens, bathrooms, lounges and even inside wardrobes. However, you need to take into account that the installation dimensions change. See diagram.

Is there a mechanism in order to fasten the bottom of the drawer to the front part without preventing adjustment?

Yes, for the assembly of the rectangular under sink insert it is necessary to make a 90º angle straight machining cut, although it is recommended to make a machining cut with a radius of 20 mm.

Concept drawer for household, kitchen and bathroom

The following video shows how you can easily assemble the Concept drawer with back panel.

The following video shows how you can easily assemble the Concept drawer.

It is only necessary to connect the machine to air with a pressure of 7-8 kg/cm2.

The RAL code of the anthracite grey finish of the sides of the Concept kitchen, household and bathroom drawer is approximately 7043.

The RAL code of the white finish of the sides of the Concept kitchen, household and bathroom drawer is approximately 9003. Although it is necessary to bear in mind that the white silk colour of said drawer is metallized and the RAL codes are for flat colours.

The board cutting dimension and the position of the hook on the front are different. However, the hole pattern of the guide rail is the same for the Concept, Vantage-Q and Slim drawers.

Due to the fact there is separate assembly on the drawer, you can mount the Concept rails on other models of drawers. However, it is not advisable, as each drawer has its own rails and its own machining distances.

In order to assemble the aluminium back on the Concept drawer it is necessary beforehand to mount the accessories corresponding to each side height onto the profile. Subsequently, we will fasten the profile to the sides of the drawer.

In order to assemble a Concept type kitchen drawer with hinges on the unit doors (hinged doors) it is necessary to use hinges with an opening angle of 165ª or to use spacers, doing so means there will be enough space to pull out the drawer.

Yes, the spacers that are user for assembling kitchen drawers are the same as hinges on unit doors (hinged doors).

Yes, the Lokbox mechanism is used to fasten the bottom of the drawer to the front part without preventing adjustment of it. It is compatible with the Concept, Slim and Vantage-Q drawers or any drawer. It is especially recommended for very wide drawers used in the furnishings of kitchens, bathrooms, lounges and even inside wardrobes. However, you need to take into account that the installation dimensions change. See diagram.

Is there a mechanism in order to fasten the bottom of the drawer to the front part without preventing adjustment?

Yes, for the assembly of the rectangular under sink insert it is necessary to make a 90º angle straight machining cut, although it is recommended to make a machining cut with a radius of 20 mm.

Vantage-Q drawer for kitchen and bathroom

The minimum unit depth required to install a Vantage-Q exterior drawer with push is calculated with the formula: Minimum depth = Depth + 38 mm.
In this case the minimum unit depth needed will be 500 + 38 = 538 mm.

The minimum unit depth required to install a Vantage-Q interior drawer with push is calculated with the formula: Min. depth = Depth + 44 mm.
In this case the minimum unit depth needed will be 500 + 44 = 544 mm.

It is recommended to mount the guide rail synchroniser with push for the Vantage-Q drawer on units with a width of more than 600 mm.

It is recommended to mount the guide rail synchroniser with push for the Vantage-Q drawer on units with a width of maximum than 1,200 mm.

The RAL code of the white finish of the sides of the Vantage-Q kitchen drawer is approximately 9003.

The RAL code of the grey finish of the sides of the Vantage-Q kitchen drawer is approximately 9006.

In order to assemble a Vantage-Q type kitchen drawer with hinges on the unit doors (hinged doors) it is necessary to use hinges with an opening angle of 165ª or to use spacers, doing so means there will be enough space to pull out the drawer.

Yes, the spacers that are user for assembling kitchen drawers are the same as hinges on unit doors (hinged doors).

In order to plan the design of a kitchen drawer unit with Vantage-Q drawers, we need to bear in mind several parameters, this work is made easier with a help table to configure those units.

This calculation table makes it possible to calculate the position of the guides, depending on the dimensions of the unit and the number of drawers.

Also, it makes it possible to choose different heights of drawer, consequently it calculates the height of the façade of each of them within the same unit.

What different heights of drawer can I combine in a kitchen drawer unit with Vantage-Q drawers?

Documents:

Download

In order to plan the design of a kitchen drawer unit with Vantage-Q drawers, we need to bear in mind several parameters, this work is made easier with a help table to configure those units.

This calculation table makes it possible to calculate the position of the guides, depending on the dimensions of the unit and the number of drawers.

Also, it makes it possible to choose different heights of drawer, consequently it calculates the height of the façade of each of them within the same unit.

How can I plan the design of a kitchen drawer unit with Vantage-Q drawers?

Documents:

Download

We have different heights of sides and accessories that make it possible to create different types of drawers.

You can design inner and exterior drawers, with a large capacity for saucepans, with rounded or square rails, with inside accessories and even glass sides.

What types of drawers can I design for a kitchen with Vantage-Q drawers?

Yes, the Lokbox mechanism is used to fasten the bottom of the drawer to the front part without preventing adjustment of it. It is compatible with the Concept, Slim and Vantage-Q drawers or any drawer. It is especially recommended for very wide drawers used in the furnishings of kitchens, bathrooms, lounges and even inside wardrobes. However, you need to take into account that the installation dimensions change. See diagram.

Is there a mechanism in order to fasten the bottom of the drawer to the front part without preventing adjustment?

Yes, for the assembly of the rectangular under sink insert it is necessary to make a 90º angle straight machining cut, although it is recommended to make a machining cut with a radius of 20 mm.

The following video shows how you can easily assemble the Vantage-Q drawer.

The following video shows how you can easily assemble the Vantage-Q drawer.

Ultrabox drawer for kitchen and bathroom

The RAL code of the white finish of the sides of the Ultrabox kitchen drawer is approximately 9001.

The RAL code of the aluminium finish of the sides of the Ultrabox kitchen drawer is approximately 9022.

Yes, the Lokbox mechanism is used to fasten the bottom of the drawer to the front part without preventing adjustment of it. It is compatible with the Slim and Vantage-Q drawers or any drawer. It is especially recommended for very wide drawers used in the furnishings of kitchens, bathrooms, lounges and even inside wardrobes. However, you need to take into account that the installation dimensions change. See diagram.

Is there a mechanism in order to fasten the bottom of the drawer to the front part without preventing adjustment?

Drawer slides

No, the drawer length is 10 mm longer in the case of the Silver rail. Also, the position of the adjustment and locking pivot is different.

The locking pivots that are mounted on the Silver guide rails are designed in order to easily fasten the drawers to the guide rails, thus preventing them from falling during transportation or handling.

These pivots avoid the use of additional screws and for their assembly you only need a small hole in the side of the drawer. In this manner the drawer can be assembled and disassembled as many times as you wish.

There is a blocking pin that is designed in order to be able to fasten the drawers to the hidden Slippe rails simply and affordably, thus avoiding them from falling during transport or handling. There are also two different models, one for total extraction rails and another longer model for partial extraction rails.

With this pivot, you avoid the use of additional screws, and in order to assemble it you only need a small hole in the side wall of the drawer. In this manner the drawer can be assembled and disassembled as many times as you want.

It is enough to use a single locking pin in order to fasten a drawer to the hidden Slippe rails. For assembly, you only require a small hole in the side of the drawer rack as indication in the catalogue´s machining diagrams. In this manner the drawer can be assembled and disassembled as many times as you want.

The adjustment of the hidden runners for Slippe drawers without a hook is achieved by turning the washer on the front fastening pivot, which is screwed for that purpose.

The following video shows how you can easily assemble a drawer with soft-closing and T30 drop runners.

The RAL code of the white finish of the rails for T30 drawers is approximately 9001.
The RAL code of the black finish of the rails for T30 drawers is approximately 9005.
The RAL code of the grey finish of the rails for T30 drawers is approximately 9022.

Drawers for office

It is recommended to mount 2 soft-close devices per each Padplast drawer with the corresponding actuator, one on the right and another on the left of the drawer although they do not have sides.

Yes, the soft closing for the Padplast office drawer is compatible with the 27 mm high Paddock guide rails with partial extraction and the 35 mm high Paddock guide rails with total extraction, aside from the 45 mm high Paddock guide tails with total extraction because it already has soft closing.

Also, the soft closing for the Padplast office drawer is not compatible with the anti-overturn Paddock lock.

Multimedia accessories

At Emuca we have two models of Circum cable grommets, a 60mm diameter and an 80 mm diameter. For large plugs it is advisable to use the Circum cable grommet with an 80 mm diameter.

The motorised Lift Vision television stand needs a minimum of 5 kg to function. If you want to test out its functioning without any television secured to it, then it is possible that it will carry out the raising motion but not the lowering movement. You can resolve that by simply placing the television or an equivalent weight on it.

The size of television sets or monitors is linked to the measurements of the VESA stands. This measurement is the distance that exists when you measure between the screw holes for assembly.

The motorised Lift Vision television stand is compatible with telelvisions or monitors with the following VESA measurements between holes: 200 x 100, 200 x 200, 300 x 300, 400 x 200, 400 x 400, 600 x 400 mm, and other measurements such as 400 x 100, 600 x 100, and 600 x 200 mm.

In the following table you can find a list with the equivalents that will allow you to have a more approximate idea of the stand that you need.

What is the size of the television set or equivalent monitor with a VESA stand and with the motorised Lift Vision stand?

The majority of televisions or monitors are compatible with VESA stands. You can check that in the back part of the device there is a square or rectangle comprised of holes for assembly with screws. If that is the case, the television or monitor is compatible with VESA stands.

 

The Quadrum cable grommet makes it possible to pass through cables of any thickness and hide their connections easily, enabling access to them at all times thanking to its folding cover and its black plastic filaments.

It is designed to be embedded into a worktop or a table with prior machining of 147 x 68 mm for the model code. 5010062 and 257 x 68 mm machining for the model code. 50124. It is fastened via clipping and can be mounted on very thick surfaces.

 

There are two options:

- Without using the rubber trim: remove the cover and the rubber trim, pass the cable through the through-hole and place the cover on again but without the rubber trim.

- Using the rubber trim: it is possible to make a small cut to the rubber with a cutter, in a way that makes it possible to insert the cable and thus be able to keep the rubber mounted on the cable grommet. (Recommended).

What do I need to do in order to pass a cable with a large plug through the Circum cable grommet?
Technical questions box

You can not find the information you need? Raises your technical questions about our products and our technical department will solve.